Support / My Reolink camera appears in its own app, but ViewTile cannot connect.
Reolink RTSP URL and ONVIF: ports and setup
Last updated:
In short
A Reolink RTSP URL usually ends in /Preview_01_main or /Preview_01_sub, with RTSP on port 554 and ONVIF on port 8000. Availability depends on the camera and whether it connects through a recorder or Home Hub, according to Reolink’s documentation (read 16 November 2026). ViewTile has not been tested with Reolink cameras.
Which Reolink products offer RTSP and ONVIF
Check the Reolink protocol availability list before changing settings. The product name, hardware version and power mode matter.
- Standalone access is listed for E1 Pro, E330, Lumus Pro E450, RLC, Duo, E1 Outdoor and professional series cameras.
- A Home Hub or NVR is required for battery Wi-Fi cameras such as Argus, Altas and the battery doorbell; kit cameras without a UID such as D500, B800, B500W and V800W; E1; E320/E321; and Lumus E430 hardware IPC_325C7.
- The listed 4G LTE cameras, including Go, TrackMix LTE and Duo 2 LTE, do not offer these protocols.
- Battery Doorbell 2nd generation offers RTSP and ONVIF only in wired power mode with the latest firmware.
Battery Wi-Fi cameras in the hub or recorder category do not offer standalone RTSP or ONVIF. Adding their own address in ViewTile cannot enable those services.
The Reolink RTSP URL
Enter credentials in ViewTile’s separate username and password fields. Replace CAMERA_IP or NVR_IP with the device’s local IP address.
| Purpose | Stream address |
|---|---|
| Camera main stream | rtsp://CAMERA_IP:554/Preview_01_main |
| Camera substream | rtsp://CAMERA_IP:554/Preview_01_sub |
| NVR channel 2 main stream | rtsp://NVR_IP:554/Preview_02_main |
| Older H.264 main spelling | rtsp://CAMERA_IP:554/h264Preview_01_main |
| Older H.264 substream spelling | rtsp://CAMERA_IP:554/h264Preview_01_sub |
| Older 4K H.265 main spelling | rtsp://CAMERA_IP:554/h265Preview_01_main |
Start with Preview_. Reolink’s older examples also use the codec-prefixed spellings, including h265Preview_01_main with h264Preview_01_sub for some 4K cameras. These are alternatives to check against your camera’s documentation, not interchangeable paths for every model.
The current RTSP instructions specify default port 554, which may be omitted when unchanged. Use the configured port if it differs. For an NVR address, use the NVR’s credentials and the required channel number.
Those instructions also warn that 4K cameras on NVR hardware H3MB16, H3MB02 or H3MB17 offer RTSP only in fluent mode. Battery cameras accessed through a hub or NVR can end preview after five minutes and stop RTSP when asleep. Reolink recommends a request timeout of at least 20 seconds for that arrangement; ViewTile has no documented setting for that timeout.
Enable RTSP and ONVIF
Reolink documents ONVIF port 8000 and RTSP port 554 as defaults. Check the actual values before entering them.
The port settings guide says most cameras have these services disabled by default. Cameras with smart person, vehicle or pet detection have service switches; cameras without that detection have no switches and their ports are enabled.
- In the Reolink app, open the camera’s gear icon, then More Features > Advanced Network Settings > Server Settings.
- Enable RTSP and ONVIF, and note their ports. In the web interface, the documented route is Device Settings > Network > Advanced > Server Settings, sometimes followed by Set Up.
- For a camera accessed through an NVR, use NVR Settings > Network > Advanced > Port Settings. For a Home Hub arrangement, open the services on the hub.
These changes belong on the camera, recorder or hub. ViewTile cannot turn on a disabled service.
Add it in ViewTile
- From the empty camera wall, tap Add a camera, then Find cameras.
- If nothing appears, try Search deeper. It takes about a minute. Discovery failure does not prove that the camera lacks ONVIF.
- Choose Type the camera address instead if needed. In Camera address, enter the camera, hub or NVR IP, its ONVIF port and its device username and password.
- Run the connection test. Read the first failed step, from Camera reachable through Stream address.
- To use RTSP directly, select Stream address, paste a URL from the table and fill in the separate credential fields.
A stream address provides video only. It does not provide pan and tilt, picture settings, clock checks, recordings or diagnostics beyond playback.
When it fails
Reolink’s RTSP and ONVIF troubleshooting guidance covers disabled ports, firmware, login lockout and password characters.
- Port closed: the device answered, but the chosen service did not. Check the ONVIF switch and port on the camera or recorder.
- Not an ONVIF device: an HTTP service answered without an ONVIF response. Verify the ONVIF port rather than entering the web interface port by assumption.
- Wrong username or password: check the device credentials. Repeated attempts can trigger Illegal Login Lockout. Resolve the lockout in the device settings before retrying. Reolink also advises avoiding special characters when troubleshooting RTSP passwords; do not move credentials into the URL.
- No video from this camera: ViewTile received no video after three attempts over TCP and then UDP. Check the RTSP switch, port, channel and path. Try the substream to distinguish a main-stream problem from a connection failure.
- Stream keeps dropping: check Diagnostics for an ONVIF camera. If it still answers, lower bitrate or select the substream. Otherwise, investigate its network connection.
Reolink’s online-user documentation lists two clear plus ten fluent viewers for PoE/Wi-Fi cameras and NVRs, with two plus two for E1, E1 Pro and Lumus. Battery figures vary. It does not mean whether RTSP sessions count toward those totals. Closing unused live views is a useful check, not proof that a limit caused the failure.
For ONVIF cameras, Video streams selects wall and full-screen streams. ViewTile normally uses the substream on the wall and can fall back to it when the main stream cannot keep up.
Find the IP address
Reolink’s IP address instructions give the app route as gear > Device Info > IP Address, or More Features > Network Information. On an NVR monitor, Network > Network Status shows the recorder address; Camera > select camera shows a camera address.
Related articles
See Adding a camera by its stream address, ONVIF camera not found, Cameras behind a recorder and Main stream vs substream.

