Support / My Hikvision camera has an IP address, but ViewTile cannot log in or show video.

Hikvision RTSP URL and ONVIF setup

Last updated:

In short

A Hikvision RTSP URL commonly uses /Streaming/channels/101 for the main stream and /Streaming/channels/102 for the substream. For ONVIF, enable the service, check its HTTP port and create the appropriate ONVIF user before adding the device in ViewTile.

These settings are according to Hikvision’s documentation (read 16 November 2026). ViewTile has not been tested with Hikvision cameras. Menu labels and available settings depend on the device and firmware.

Build the Hikvision RTSP URL

Use the camera’s actual IP address and RTSP port. Keep credentials out of the URL in ViewTile: enter them in the separate username and password fields.

Stream URL pattern
Camera or recorder channel 1, main rtsp://IP:554/Streaming/channels/101
Camera or recorder channel 1, sub rtsp://IP:554/Streaming/channels/102
Recorder channel 2, main rtsp://IP:554/Streaming/channels/201
Recorder channel 3, sub rtsp://IP:554/Streaming/channels/302
Documented ISAPI form rtsp://IP:554/ISAPI/Streaming/channels/101

Hikvision’s RTSP support article uses the path without /ISAPI. Its protocol documentation also uses the ISAPI form. Follow the form documented for your device rather than changing unrelated settings when one path fails.

The channel ID is (channel number × 100) + stream type. Stream type 1 means main, 2 means sub and 3 means third stream where offered. On a hybrid recorder, digital channels follow the analog channels: a recorder with 16 analog channels can start its IP channels at 17. Use the recorder’s IP address and confirm its channel numbering.

Hikvision’s camera manual says the RTSP port defaults to 554 and can be changed under Network > Basic Settings > Port. Use the configured value after the colon in your URL.

The US support article also mentions 10554. Treat it as a Hikvision USA recommendation, including situations where carriers block 554, not as a second default or a requirement for password authentication. For local viewing, check the device’s configured port instead of substituting 10554 automatically.

Enable ONVIF and check the port

Hikvision’s ONVIF guide says the service uses the HTTP port, normally 80, and follows a customized HTTP port. Do not enter RTSP port 554 as the ONVIF port. Also do not assume that an SDK port is the ONVIF service.

For a camera, Hikvision’s ONVIF setup instructions give this sequence:

  1. Open Configuration > Network > Advanced Settings > Integration Protocol on the camera.
  2. Enable ONVIF. Some firmware calls it Enable Open Network Video Interface.
  3. Follow the documented Hikvision CGI setting on that page, including its digest/basic authentication option where present.
  4. Click Add to create an ONVIF user. Enter that user’s credentials in ViewTile.

Media User permits live streaming and reading configuration. Operator permits most settings, while Administrator has broader access. Choose the access needed for the task.

For a recorder, Hikvision’s NVR instructions put ONVIF under Maintenance > System Service > ONVIF. Enable it and add a user there. The documented NVR setup has ONVIF disabled by default.

Hikvision’s firmware guidance describes a change around V5.5.0: newer camera firmware requires ONVIF to be enabled and a separate user created, while older firmware may use the camera login. Check the actual device settings rather than relying on the version alone. A factory reset can remove ONVIF users.

Add it in ViewTile

  1. Connect the phone or tablet to the camera’s local network. On the empty wall, tap Add a camera.
  2. Choose Find cameras. If nothing appears, Search deeper checks additional ports and takes about a minute.
  3. To enter it yourself, choose Type the camera address instead, then Camera address.
  4. Enter the IP address, ONVIF HTTP port and ONVIF user’s credentials.
  5. Run the connection test. It checks Camera reachable, Camera speaks ONVIF, Clock check, Login, Camera details, Video streams and Stream address, in that order.
  6. If ONVIF is unavailable but the device offers RTSP, use Stream address with a URL from the table and separate login fields.

The stream address route supplies video only, without ONVIF controls, clock checks or recordings. For an ONVIF camera, Video streams chooses the streams used by the wall and full screen.

Match the failure to the setting

Port closed means the camera answered but nothing listened on the entered port. Check the camera’s HTTP/ONVIF port and whether ONVIF is enabled. This fix belongs on the camera or recorder.

Not an ONVIF device means an HTTP service answered without an ONVIF response. Recheck Integration Protocol, or the recorder’s System Service page, and the service port. A working web page does not mean that ONVIF is enabled.

Wrong username or password or Credentials needed points to the login. Check the separate ONVIF user before retrying repeatedly. Changing the ordinary camera login is not a substitute for checking that account.

Camera clock is off points to timestamp authentication. Hikvision’s support notice about ONVIF failures with newer firmware describes an anti-replay time check that can reject ONVIF login when clocks differ. ViewTile compensates for a stable offset, but cannot compensate when the clock drifts between measurements. Fix the camera’s time or enable NTP, then retry.

No video from this camera after an ONVIF connection means no video arrived in three attempts over TCP and then UDP. Check the configured RTSP port and the returned stream address in Diagnostics. A blocked route belongs to the network configuration; a wrong port or path belongs to the camera or recorder setup.

The tile’s short failure reason also appears under Recent events. For an ONVIF camera, use Copy report for support in Diagnostics to collect a report with passwords redacted.

Find the camera’s IP address

Hikvision’s documentation describes SADP for finding devices on the same physical subnet. Its tools pages now direct users toward HiTools Delivery. The camera FAQ lists historical defaults of 192.168.1.64 for newer firmware and 192.0.0.64 for older firmware; neither proves your camera still uses that address.

For a camera behind an NVR, Hikvision’s camera access instructions describe NVR Menu > Camera and Virtual Host. A camera address on the recorder’s private network may not be reachable directly from your phone.

See Adding a camera by its stream address, Password refused or clock off, Cameras behind a recorder and IP camera found but no picture for the corresponding next steps.